• <dd id="uqmck"></dd> <dd id="uqmck"></dd>
    <menu id="uqmck"></menu>

    秸稈顆粒機具備的高行程有哪些?

    來源:http://www.3buildersinc.com 發布時間:2020-07-20 瀏覽次數:
    控制粗纖維材料的含量。 粗纖維是秸稈造粒過程中非常重要的因素。 含量太多,粘結性差,難以壓制成型,含量太小,不利于成型。 通常,對照約為5%。 我們會聯系具體的價值。 我們根據您的具體情況給出計算結果。
    Control the content of crude fiber material. Crude fiber is a very important factor in the process of straw granulation. Too much content, poor adhesion, difficult to press molding, content is too small, not conducive to molding. Generally, the control is about 5%. We will link specific values. We give the calculation results according to your specific situation.
    添加油脂。 當秸稈顆粒機用作燃料顆粒機時,需要向材料中加入適量的油,約0.8%。 添加潤滑脂有兩個優點,一是減少機器的磨損,提高機器的使用壽命。 其次,材料變得易于壓制和形成并增加產量。 應該指出的是,控制量不應過多。 添加方法通常是在混合攪拌部分中添加30%,并在造粒機中噴灑70%。 如果你使用秸稈顆粒機制作飼料顆粒,不要,或者你不能吃顆粒狀的動物。
    Add grease. When straw granulator is used as fuel granulator, it is necessary to add an appropriate amount of oil, about 0.8%. Adding grease has two advantages. One is to reduce the wear of the machine and improve the service life of the machine. Second, the material becomes easier to press and form and increase yield. It should be noted that the amount of control should not be excessive. The addition method is usually 30% in the mixing and mixing section and 70% spraying in the granulator. If you use a straw pelletizer to make feed pellets, don't, or you can't eat granular animals.
    秸稈顆粒機廠家
    水分控制在13%左右。 對于生物質燃料,應嚴格控制材料的水分。 這是將材料壓成顆粒的前提。 如果水分太高,顆粒會松動。 這不是很多,但請記住。
    The moisture content was controlled at about 13%. For biomass fuel, the moisture content should be strictly controlled. This is the premise of pressing the material into particles. If the moisture is too high, the particles will become loose. It's not a lot, but remember.
    如果生物質秸稈顆粒機使用不當,產量將低于標準預期產量。 如果使用時間很長,則產量會下降。 作為生物質木質顆粒的制造商,我們有以下建議。
    If the biomass straw granulator is not used properly, the output will be lower than the standard expected output. If used for a long time, the yield will decrease. As a manufacturer of biomass wood particles, we have the following suggestions.
    1.調整原料的水分含量。 抑制生物質顆粒所需的鋸末和鋸末等原料的水分含量約為13%。 太高或太低都會降低產量。
    1. Adjust the moisture content of raw materials. The moisture content of sawdust and sawdust is about 13%. Too high or too low will reduce the yield.
    2.調整顆粒機的參數。 例如,壓力輥和模具之間的間隙。 不同材料需要不同的間隙。 輸出低,可能是間隙未正確調整。 讓制造商調整它。
    2. Adjust the parameters of the granulator. For example, the gap between the pressure roller and the mold. Different materials require different clearances. The output is low, the gap may not be adjusted correctly. Let the manufacturer adjust it.
    3.新模具應磨削。 限于秸稈顆粒機的機械制造水平,新模具的模腔平滑度達不到秸稈顆粒機的水平。 研磨方法也很簡單,好多次按壓油,沙和木屑的混合物。 詳細過程可以詢問制造商,或聯系我們的客戶服務。
    3. The new mould should be ground. Limited to the mechanical manufacturing level of the straw granulator, the smoothness of the cavity of the new mold can not reach the level of the straw granulator. The grinding method is also very simple. Press the mixture of oil, sand and sawdust many times. Detailed process can be asked the manufacturer, or contact our customer service.
    4.做好機器維護,及時更換模具。 模具和壓輥秸稈顆粒機需要很長時間才能引起磨損,這是不可避免的。 如果這是生產下降的原因,好更換新模具。
    4. Do a good job in machine maintenance and timely replace the mold. It takes a long time for the mould and press roller straw granulator to cause wear, which is inevitable. If this is the reason for the decline in production, replace the mold with a new one.
    感謝您的閱讀,此文的文章來源:秸稈顆粒機廠家更多的內容和問題請點擊:http://www.3buildersinc.com我們會繼續努力的為您提供服務,感謝您的支持!
    Thank you for your reading. This article is from: straw granulator manufacturer. For more information and questions, please click: http://www.3buildersinc.com We will continue to work hard to provide services for you, thank you for your support!

    上一篇:生物質顆粒機壓軸打滑問題怎么處理?、

    下一篇:最后一頁

    幸运快三